"ZERTIFICAT" V8130, professional product is acryl- styrene paint in water dispersion.
Main characteristics: coating class 1, according to European Standard 13300 (very good covering capacity); super washable product, excellent whiteness; yellowing resistance; excellent adhesion to absorbent and non-absorbent substrates, optimal applicability, allows walls to breath because the film is permeable for water vapors, short drying time, can be tinted with tinting products KOBER brand, the product is non-pollutant good leveling, very good resistance to ageing, ecologic product.
It can be applied on interior on all types of masonry, plaster, concrete, gas-formed, concrete, rigid building boards, plaster boards, renders, asbestos cement or other building materials.
This product has Number 1- 010/2008 emitted by Paint and Lacquers Institute from Magdeburg- Germany. V8130 product has technical approval Nr. 016-04/757-2008 elaborated by ICECON Bucharest and emitted by Permanent Technical Committee for Construction.
Aspect | thixotropic, suspension viscous | visual |
---|---|---|
Color | white | visual |
Non-volatile content, 0.5g/50cm2, 125°C, 25 minutes | 67 ± 1% | SRENISO 3251: 2003 |
Viscosity batten-cone, cone type 0-10P, 900 rot /minute, 25°C | 2,45 - 2,65P | SRENISO 2884-1:2006 |
pH | 8,0 - 8,5 | According to intern norm |
Density, 23°C | 1,65 ± 0,05 g/ml | cf. norma interna |
Covering power | 1 - 2 coats | Practical determination |
Package availability | 24 months from the production date, with the observance of the storage and packing provisions. Depending on the storage conditions, it is recommended to stir the product before use. |
Aspect | matt | visual |
---|---|---|
Minimum whiteness | 90 - 92% | Data Color Equipment |
Drying time at 23 ± 2°C, 50 ± 5% relative humidity, time for deep/ handle dry (D type) | 60 minutes | ASTMD 1640:2003 |
Application method | rolling, brushing | |
---|---|---|
air-spraying | 3,0 bars air pressure, nozzle: 1.5 mm | |
air-less spraying | 150-250, pulverize angle: 40°, nozzle: 0.013-0.026 mm | |
Thinner used / dilution: clean, cold water (15-25°C) | rolling, brushing | |
air-spraying | 3,0 bars air pressure, nozzle: 1.5 mm | |
air-less spraying | 150-250, pulverize angle: 40°, nozzle: 0.013-0.026 mm | |
Re-covering period | minimum 60 minutes | |
Specific consumption is dependent of surface porosity and preparation | up to 16.0 m2/L/coat Practical spreading rate depends on the application conditions (surface geometry, application method, environmental conditions, type and surface preparation). | Practical determination |
- The surfaces are even with pumice stone, freestone, well burned brick, through circular moves and maintaining permanent contact with plaster surface. For big surfaces it is recommended to use electric polishing equipment;
- It is recommended to open the cracks with a knife and filled with cement binder, plaster or other filling material. For cracks smaller than 2mm use "Stuc C 4000". For higher cracks thick, it is recommended successively application of more coats with stuc, with intermediary polishing and dust;
- The plaster which, through knocking, show cracks or some other irregularities are totally removed, until the masonry. If the surface is small it can be repaired with concrete pasta with fast drying; on big surfaces use cement binder of the same type with the plaster;
- The finishing pasta is made of plaster pasta or "Stuc" C 4000, the last one being very white, with fast drying and very good polishing capacity after complete drying;
- praful rezultat din netezirea suprafetelor se indeparteaza cu perii, maturi sau se sufla cu aer comprimat;
- anulatiile de nisip mai mari, evidente pe suprafata tencuielii, trebuie indepartate deoarece se vor desprinde cu timpul impreuna cu finisajul, prin atingere;
- All the period for repairing and plastering the recommended temperature is at least 5°C;
- The plaster need at least 24 hours for complete dry before applying the last finishing coat.
For best results on surfaces plastered with APLAFILL or CT 127 skim it is recommended initial application of one layer of G 8105 "KÖBER Putzgrund Weiss".
Given a properly prepared surface is only necessary to apply one coat of V 8130 paint.
- The plaster condition is checked through knocking; if there are surfaces or borders that will fall they need to be repaired with new plaster;
- Old, un-adherent paint are totally removed through erasing with steel spatula or burning with gas lamp;
- Paints based on glue are totally removed;
- Surfaces affected by fungus or mold need to be cleaned and well impregnated with anti-mold solution AS8000, and after that the anti-mold primer, G8107, is applied and needs total dry.
- If the surface need to be repaired it is recommended to use cement pasta, plaster cement or others materials adequate for consolidation; the dust, from polishing after repairing, is removed.
- The purpose of the step is to impregnate the support and to fix the coat that already exist on the wall, in case that this previous coat is resistant and does not need to be removed;
- Through priming the surface is uniformed so the last coat will be perfect, without spots;
- Furthermore, the primer rises the adherence between the surface and the product we want to apply;
- Priming is mandatory and requires at least one primer G8101 coat, diluted 1:5 with cold, clean water (15-20°C); for best result it is recommended applying one coat of white primer "Putzgrund Weiss" G8105, diluted maximum 10% with clean water (15-20°C); if it is necessary (the surface was affected by fungus or mold) instead of G8101 primer, you need to apply 1-2 coats of anti-mold primer, G8107, after previously cleaning the surface with anti-mold solution, AS8000.
- The primer is applied only after complete drying;
- The surfaces have new plaster or repairing require additional priming because of the high absorption grade;
- After complete drying the product may be applied.
- environment relative humidity: max.70%
- environment and surface temperature: 10 - 30°C
- it is recommended the ventilation the working place.
- Brushing or rolling: the first coat is applied diluted with approx. 10% cold, clean water (15-20°C); after complete drying (minimum 60 minutes) the second coat is applied (if it is necessary), without dilution or diluted with approx. 10% cold, clean water (15-20°C);
- Air-spraying (pressure: 3 bars; nuzzle 1.5 mm): 1-2 coats are applied with approx. 40% dilution with cold, clean water (15-20°C);
- Air-less spraying (pressure: 150-250 bars, nozzle: 0.013-0.026, pulverization angle 40°): 1-2 coats are applied, without dilution.
The used instruments are washed with water, immediately after application.
Please contact the producer for further information.
Phone: 0040 233 281021,
Fax: 0040 233 281222,
E-mail: office.savinesti@kober.ro
Fiscal code: RO 2005144
Registration number in Romanian Trade Register: J27/1405/1991
Social capital: 26,733,653.25 RON
- 0372 322412
- 0372 322413
- 0372 322414
- 0372 322415
- 0372 322416
- 0233 202412
- 0233 202413
- 0233 202414
- 0233 202415
- 0233 202416
Phone: 0233 281021, 0372 322409
E-mail: monica.apetroaei@kober.ro
Fax: 0233 234450; 0233 290700
E-mail: office@kober.ro
Phone: 0233 202421
Phone: 0040 722 619540
E-mail: kalman.nagy@kober.ro
Acest site foloseste cookie-uri. Continuarea navigarii pe site reprezinta acordul dumneavoastra pentru folosirea cookie-urilor. Mai multe informatii aici.
The cookie settings on this website are set to "allow cookies" to give you the best browsing experience possible. If you continue to use this website without changing your cookie settings or you click "Accept" below then you are consenting to this.